$$$$ DEPL NOTICE BP208322 13/06/27 21:15:07 7783 DATE 13/06/27 Directive DEPLACER Voir aussi : PLUS TOUR ------------------ MOIN SYME AFFI PROJ HOMO DEDU DEPL GEO1 |'PLUS' | | VEC1 | ; |'MOINS'| | CHPO1 | ; |'COOR' | 'CYLI' POIN1 POIN2 (POIN3 SI 3D) ; | | 'CART' ; |'TOUR' | ANGL1 | POIN1 (POIN2 SI 3D) ; | | CHPO1 | |'HOMO' RAPP1 POIN1 ; |'AFFI' RAPP1 POIN1 POIN2 ; |'SYME' | 'POIN' POIN1 ; | | 'DROIT' POIN1 POIN2 ; | | 'PLAN' POIN1 POIN2 POIN3 ; |'PROJ' |('CYLI') VEC1 | |'PLAN' POIN1 POIN2 POIN3 ; | | 'CONI' SOMM1 | |'SPHE' CENT1 POIN1 ; | |'CYLI' CENT1 CENT2 POIN1 ; | |'CONI' POIN1 POIN2 POIN3 ; | |'TORI' CENT1 POIN1 POIN2 POIN3 ; | |'DROI' POIN1 POIN2 ; | |'CERC' CENT1 POIN1 ; |'COOR' | 'CYLI' POIN1 POIN2 ( POIN3 SI 3D) ; | | 'CART' ; |'MILI' ; |'BARS' | POIN1 | (FLOT1) ; |'DEDU' | GEO2 GEO3 ; | CHP1 ; Description: ____________ The DEPLACER instruction aims at displacing all the points that pertain to the GEO1 object (MAILLAGE or POINT type) without creating any new object. Contents: _________ With the following keywords: 'PLUS' : a translation of the VEC1 vector (POINT type) or the CHPO1 field (CHPOINT type) is applied to the set of points 'MOINS' : a translation of the -VEC1 vector (POINT type) or the -CHPO1 field (CHPOINT type) is applied to the set of points 'TOUR' : a rotation of ANGL1 angle (FLOTTANT type) or of angle defined by CHPO1 (CHPOINT type) about POIN1 (POINT type) in 2D or about the axis defined by POIN1 POIN2 (POINT type) in 3D is applied to the set of points 'HOMO' : an homothety of POIN1 centre (POINT type) and RAPP1 ratio (FLOTTANT type) is applied to the set of points 'AFFI' : an affinity leaving the POIN1 (POINT type) unchanged of direction defined by (POIN2 - POIN1) and RAPP1 ratio (FLOTTANT type) is applied to the set of points 'SYME' : a symmetry connected with the requested operation : - 'POIN' = with respect to the POIN1 point (POINT type) - 'DROI' = with respect to the straight line POIN1 POIN2 (POINT type) - 'PLAN' = with respect to the plane POIN1 POIN2 POIN3 (POINT type) is applied to the set of points 'PROJ' : a CYLIndrical projection according to the direction defined by the VEC1 vector (POINT type) or a CONIcal projection of centre SOMM1 (POINT type) is applied to the set of points on the requested surface: - PLAN defined by the points POIN1 POIN2 POIN3 (POINT type) - SPHERE of CENT1 centre passing through the POIN1 point (POINT type) - CYLINDRE whose axis passes through the points CENT1 and CENT2 (POINT type) - CONE of POIN1 apex (POINT type) whose axis passes through the POIN2 point, and contains the POIN3 point (POINT type) - TORE of CENT1 centre whose axis passes through the POIN1 point, a small circle centre of which is the POIN2 point and which contains the POIN3 point. In 2D, the projection is performed onto a line: - DROIte defined by the points POIN1 and POIN2 (POINT type) - CERCle of CENT1 centre passing through the POIN1 point (POINT type) 'COOR' : a change of coordinate system is done between the cartesian and the cylindrical coordinates 'CYLI' : cylindrical coordinates are wanted. The angles vary from -180 to +180 degrees. In 2D, POIN1 is the centre of the coordinate system and the line defined by POIN1 to POIN2 gives the null theta angle. In 3D, POIN1 is the centre of the coordinate system, the axis defined by POIN1 to POIN2 is the positive Z-axis and the plane defined by the three points POIN1 POIN2 and POIN3 gives the null theta angle. 'CART' : cartesian coordinates are wanted. The supplied angles must be expressed in degrees varying from -180 to +180. In 2D, the origin of the basis does not change and the X-axis corresponds to theta equals zero. In 3D, both the origin and the Z-axis do not change; the X-axis corresponds to theta equals zero. 'MILI' : Midle nodes of quadratic element are put on the median plane of the two end nodes. 'BARS' : Middle nodes of quadratic elements are moved in order to create Barsoum's element a the crack point. The crack point is given via POIN1, the crack edge via GEO2. Only the middle nodes of quadratic elements at the crack edge are moved, no point of the crack edge is moved. FLOT1 is the curvilinear coordinate of the moved nodes. If FLOT1 is not specified, it is set to 0.495 (the nodes are moved to the quarter of the edge of the element toward the crack point). 'DEDU' : Nodes of GEO1 object are moved according to the linear application defined by the movement which put the N nodes of GEO2 on the N nodes of GEO3. In case of the data CHP1 (displacements field), nodes supporting CHP1 are nodes of GEO2 and GEO3 is obtained by application of the displacements field to GEO2. IMPORTANT: The number of nodes N defining the framework transformation is at the most equal to (DIME+1), where DIME corresponds to the current space dimension (1, 2 or 3). Notes: ______ Contrary to the DEPLACER instruction which only displaces the GEO1 object, the PLUS, MOINS ... operators create a new object GEO2 by copying and displacing GEO1. In DIMEnsion 1, only the following operations can be used: 'PLUS', 'MOINS', 'HOMO', 'SYME' ('POIN' option) 'MILI' and 'DEDU'.
© Cast3M 2003 - All rights reserved.
Disclaimer